10 in stock
10 in stock
This is the official Busch SECURING WASHER (Part #432000220). It is a direct replacement part made for Busch Panda vacuum pumps. This washer fits four popular models: WV250B, WV250C, WV500B, and WV500C. Keep your pump hardware complete with the right washer.
This is the Edwards Water Hose for water-cooled vacuum pumps. It has 3/8 inch BSP male pipe fittings on each end. The hose is 780 mm long. It is used to connect your pump to the cooling water supply and return. A direct OEM replacement part.
This is the Kinney Water Jacket Gasket, Part# 807645. It is made specifically for the Kinney KT150C rotary piston vacuum pump . This gasket seals the water jacket, which is the hollow space around the pump cylinder where cooling water flows. A good seal here prevents water leaks. This part is also included in Preventive Maintenance Kits and Major Repair Kits for the KT150C
Leybold Sogevac pump for maintenance, this is a great time to put in a fresh wave washer. It is a low-cost part that prevents expensive problems later.
Wave Washer is used on Leybold Sogevac pump model SV500B, SV630B, SV630BF, SV750B, SV750BF
10 in stock
This wave washer (Part #71214792) is a specialized wavy spring washer used on the Leybold Sogevac SV1200 vacuum pump . The washer applies constant spring force to pre-load bearings, absorb shock, and take up dimensional tolerances
This wave washer (Part #71403192) is a specialized wavy spring washer used on Leybold Sogevac vacuum pumps. It fits models SV500, SV630, and SV630F . The washer applies constant spring force to pre-load bearings, absorb shock, and take up dimensional tolerances. It helps reduce bearing noise, eliminate vibration, and extend the life of your pump .
This wave washer (Part #971425972) is a specialized wavy spring washer used on Leybold Sogevac vacuum pumps. It fits models SV500B, SV630B, SV630BF, SV750B, and SV750BF . The washer applies constant spring force to pre-load bearings, absorb shock, and take up dimensional tolerances. It helps reduce bearing noise, eliminate vibration, and extend the life of your pump
10 in stock
This is the Edwards Woodruff Key. Part number 24301040. Also known as a half-moon key, it is used on iH and iL series dry pumps . Compatible with iH80, iH160, iH600, iH1000, iH1800, iH2400, iL70, and iL600 models . This key is included in official Edwards major repair kits
This is the Edwards WRG Body Tube Assembly for the WRG-S series Active Wide Range Gauges . It is a direct replacement sensor tube with a NW25 (KF25) vacuum flange . This component contains the Pirani and Penning gauge elements.
The X Shaft is a direct replacement part for Edwards mechanical booster pumps. It fits specifically the HCMB600 and HCMB1000 models. These booster pumps are often used together with dry pumps like the HCDP80. The X Shaft is a rotating part that helps transfer motion inside the pump. If your booster pump is noisy or not working well, a worn shaft could be the cause. Replace it and get your system back to full performance.
This is the Edwards Tip Seal for XDS5 and XDS10 dry scroll vacuum pumps . It is a critical wear component that sits in the scroll channels . This seal measures 4.03 mm in thickness and is used for a “thick wall” repair or specific scroll set . A direct OEM replacement part.
This is the Edwards Tip Seal for XDS5 and XDS10 dry scroll vacuum pumps . It is a critical wear component that sits in the scroll channels.
Not a member? Create an account
Already got an account? Sign in here
