The KF25 to 3/4″ BSP Adaptor (Part # C10501714) is a Edwards fitting. It converts a KF25 (NW25) vacuum port to a 3/4 inch BSP male thread . This adaptor is often used to connect Edwards EMF oil mist filters to pump exhaust ports.
10 in stock
This is a PFPE-lubricated ball bearing used on Edwards EH Booster and QMB Blower pumps . It fits models QMB250, EH250, QMB500, and EH500.
10 in stock
This is an S-Row ball bearing used on Edwards EH Booster and QMB Blower pumps . It fits models QMB250, EH250, QMB500, and EH500.
The Ballast Filter (Part # 25907200) is a replacement part for Edwards E1/E2M series rotary vane pumps. This small felt filter cleans the air that enters the pump through the gas ballast valve. It stops dust and dirt from getting into your pump oil. If you change your pump oil, you should change this filter at the same time. It fits E2M2, E2M5, E2M8, and E2M12 models .
The Ballast Filter (Part # 25907202) is a replacement part for Edwards E1/E2M series rotary vane pumps. This small felt filter cleans the air that enters the pump through the gas ballast valve.
10 in stock
This is a deep groove ball bearing for Edwards vacuum pumps and boosters. The dimensions are 62mm outer diameter, 30mm inner diameter, and 16mm width.
This is a bearing retainer, also known as a bearing cage, for Edwards vacuum pumps . Its job is to keep the rolling elements (balls or rollers) inside the bearing evenly spaced .
This is a single row ball bearing, size 6309, used on Edwards pump models . Single row ball bearings support radial loads and allow for smooth rotation. They consist of an outer ring, inner ring, cage, and balls that maintain separation between the rings .
10 in stock
This Coupling Baffle is a replacement part designed for the coupling cover assembly. It helps control oil flow and stops excess mist from escaping the gearbox.
The COUPLING BAFFLE EH500 is a replacement part made for the Edwards EH500 Mechanical Booster Pump. It sits inside the coupling-cover assembly. Its main job is to manage oil flow and reduce oil mist escaping from the gearbox area. This simple part helps keep your pump clean and running smoothly for longer.
The COUPLING BOSS is a replacement part made for Edwards EH Series Mechanical Booster Pumps. It is an important part of the hydrokinetic coupling assembly. This assembly connects the motor to the pumping mechanism. The coupling boss helps transmit power smoothly from the motor to the pump rotors. If this part wears out, your pump may not run correctly. Replace it to keep your pump working like new.
The COUPLING BOSS FAN ASSEMBLIES is a replacement part set made for Edwards EH Series Mechanical Booster Pumps. This assembly includes both the coupling boss and the cooling fan. The coupling boss connects the motor to the pump drive. The fan attaches to the boss and keeps the coupling area cool during operation. If your pump runs hot or the drive feels loose, this assembly may need replacement. Get both parts together in one convenient set.
The COUPLING BOSS FOR E2M28 PK1 is a replacement part made for the Edwards E2M28 rotary vane vacuum pump. This small metal part is a key piece of the drive coupling assembly. It connects the motor shaft to the pump shaft. Without a good coupling boss, the motor cannot turn the pump. If your pump is not pulling vacuum or making strange noises, this part may be worn out. Replace it to get your pump running again.
The COUPLING BOSS USA E2M28/30 is a special replacement part made for Edwards E2M28 and E2M30 rotary vane pumps.
The COUPLING COVER EH1200 C/SEAL PK 1 is a complete replacement cover for the Edwards EH1200 mechanical booster pump. It comes with the seal already included.This cover bolts onto the side of the pump where the motor connects to the pump shaft. It protects the coupling area and keeps the oil inside. If your existing cover is cracked, leaking, or damaged, this is the direct replacement you need.
The COUPLING COVER EH250/500 C/SEAL PK 1 is a complete replacement cover for the Edwards EH250 and EH500 mechanical booster pumps. It comes with the seal already included. This cover bolts onto the side of the pump where the motor connects. It protects the coupling area and holds the oil inside. If your existing cover is cracked, leaking oil, or damaged, this is the direct replacement you need. It fits both the EH250 and EH500 pump models .
Not a member? Create an account
Already got an account? Sign in here
