This printed gasket is a direct replacement for the original Edwards part. Use it during your next pump overhaul to get a perfect seal.
This is the Edwards Printed Gasket. Part number A27160004. It is designed for the QMB1200 and EH1200 mechanical booster pumps. This gasket is a critical component included in official Edwards rebuild kits . If you are servicing your booster pump, this is the part you need.
This is the PV25EKA model. It runs on 110V power (standard US voltage). The body is made of lightweight aluminum. Both ends have KF25 flanges, which is the most common size for connections.
Use it on roughing lines, backing lines, or anywhere you need automatic isolation.
This is the PV25EKA model. It runs on 220-240V power (standard for many international and industrial applications). The body is made of lightweight aluminum. Both ends have KF25 flanges, the most common size for vacuum connections .
This is the PV25MKA model. The body is made of lightweight aluminum. Both ends have KF25 flanges, the most common size for vacuum connections. It is a right-angle valve, meaning the inlet and outlet are at 90 degrees to each other. This saves space on your system.
Use it on roughing lines, backing lines, or anywhere you need manual isolation.
This is the PV25PKA model. The body is made of lightweight aluminum. Both ends have KF25 flanges, the most common size for vacuum connections. It is a right-angle valve, meaning the inlet and outlet are at 90 degrees to each other. This saves space on your system.
This is the PV40EKA model. It runs on 110-127V power (standard US voltage). The body is made of lightweight aluminum. Both ends have KF40 flanges, which fit 40mm tubing . This larger size allows much higher gas flow than smaller valves.
Use it on roughing lines, backing lines, or anywhere you need automatic isolation with higher conductance.
This is the PV40EKA model. It runs on 220-240V power (standard for international and industrial applications). The body is made of lightweight aluminum. Both ends have KF40 flanges, which fit 40mm tubing. This larger size allows much higher gas flow than smaller valves.
Use it on roughing lines, backing lines, or anywhere you need automatic isolation with higher conductance.
This is the “QDP40 MOTOR GASKET.” It sits between the motor and the pump body. Its only job is to create a perfect seal. It keeps oil inside the pump where it belongs. It also keeps dirt and moisture out.
The Quick Disconnect Female Fitting (Part # 03530015) is a Edwards component designed for rapid connection and disconnection of fluid or gas lines in vacuum systems .
The Quick Disconnect Male Fitting (Part # 03530016) is a Edwards component designed for rapid connection and disconnection of fluid or gas lines in vacuum systems .
Our REAR BRG PK1 is a direct replacement for the original Edwards part. It restores smooth operation and prevents major pump failure.
Our rear headplate is a direct replacement for the original Edwards part. It is precision machined to fit perfectly. Install this and your pump will be as good as new.
It is an oil distribution valve. Its job is to keep oil flowing in the right direction. When the pump runs, oil flows normally. When the pump stops, this valve closes and blocks oil from flowing backward into the pumping chamber .
Our retainer is a direct replacement for the original Edwards part. It fits perfectly and keeps your exhaust system working right.
This retainer is the metal ring or washer that holds the MSE seal in its proper position. It prevents the seal from moving or twisting. Without the retainer, the seal will not work correctly.
It is a metal ring that wraps around two KF flanges. You tighten the wing nut by hand. The clamp pulls the flanges together. A rubber O-ring inside the joint creates a perfect vacuum seal.
No tools are needed for basic installation. It is quick. It is reliable. It is the standard way to connect vacuum components.
Our Ringfeder locking element is a direct replacement for the Edwards part (cross-reference 26440001).
Our Ringfeder locking element is a direct replacement for the Edwards part (cross-reference E0416).
10 in stock
Not a member? Create an account
Already got an account? Sign in here
