This is the Kinney Sleeve Bearing (Part# 054109), measuring 2 1/8 inches. It is made for Kinney Rotary Piston pumps, specifically models KT500C and KT500D. The bearing helps two moving parts slide smoothly. It cuts down on friction and vibration. Plus, it can handle heavy loads and lasts a long time.
This bearing fits these exact Kinney models:
Kinney KT500C
Kinney KT500D
The large center slide pin (Part# P805005) is a key internal part that helps the piston move smoothly. If this pin is worn, your pump cannot create strong vacuum. This is the exact replacement part for these Kinney rotary piston pumps.
This is the Kinney Large Center Piston Slide, Part# 806288. It is used on the Kinney brand of Rotary Piston family . This engineered component ensures smooth and reliable pump operation. Crafted for durability, the slide is designed to fit seamlessly, providing essential support to optimize your pump’s performance . This part is also included as a critical component in Major Rebuild Kits for the Kinney KT300C and KT300D pumps .
The small outer slide pin (Part# P805004) is a key internal part that helps the piston move smoothly. If this pin is worn, your pump cannot create strong vacuum. This is the exact replacement part for these Kinney rotary piston pumps.
Kinney KMBD booster pumps running in perfect sync with this Timing Gear Set. Designed to fit both the KMBD 850 and KMBD 1600 models, this set ensures that your pump’s internal parts rotate at the right time with each other.
It is a specialized filter element used inside the oil system of E1M175 and E2M175 rotary vane pumps. It acts as a strainer to keep contaminants out of the oil flow. If you are doing a major overhaul, this is the correct OEM part.
Out of stock
It is an oil strainer filter used inside large Edwards rotary vane pumps. It is designed for the E1M275 and E2M275 pump models. If you are doing a major overhaul, this is the correct OEM part.
It is an internal filter component that helps trap oil mist from the exhaust gases of your vacuum pump. If you are servicing your MF100 filter, this is the correct OEM replacement part .
It is the plastic knob used to operate the gas ballast valve on your vacuum pump. If your old knob is broken, cracked, or missing, this is the direct OEM replacement part
This is the L-Shaped Cork Gasket for DVP LB.40 Series vacuum pumps. It is designed to fit specific right-angle connections on the pump intake and exhaust ports. Made from high-quality cork, it provides a reliable seal against oil and air leaks.
This gasket is made for the DVP LB.40 Series. The LB.40 is a reliable rotary vane vacuum pump .
It is used on Stokes 306 and 310 mechanical booster pumps . A labyrinth seal is a non-contact sealing device that prevents oil and gas from leaking along the rotating shaft. These pumps require four of these seals per pump .
It is used on large mechanical booster pumps (often called Roots blowers). A labyrinth seal is a non-contact sealing device that prevents oil and gas from leaking along the rotating shaft. If you are rebuilding your booster pump, this is the correct OEM part.
It is used on large mechanical booster pumps (often called Roots blowers). A labyrinth seal is a non-contact sealing device that prevents oil and gas from leaking along the rotating shaft. This is the “rotating” half of the seal assembly. If you are rebuilding your booster pump, this is the correct OEM part.
It is a non-contact seal that prevents oil and gas from leaking along the rotating shaft. Each pump requires four of these seals . If you are rebuilding your 306 or 310 booster pump, this is the correct OEM part.
10 in stock
The part number is C41790200. It is a right-angled isolation valve with NW25 flanges. It runs on 24V AC or DC power. The valve is opened electrically by a solenoid and closed by a spring when power is removed. If you need to automate gas flow control in your vacuum system, this is the correct OEM valve.
This is a Edwards replacement power cord (lead assembly). It is rated for 10 amps and has a standard US plug (NEMA 5-15P).
It is rated for 16 amps and has a standard US plug (NEMA 5-15P). The other end has a C19 connector, which is a high-current “figure-8” or “household” shaped socket. This cord is designed for larger Edwards pumps, such as the iH series, E1M18, E2M18, and E2M28, that require a higher current supply
10 in stock
Not a member? Create an account
Already got an account? Sign in here
